RIVETT 608 Metal Lathe Bulletin/Manual 0578
Manual Description: Number of Pages: 32 This is a reproduction, not a photocopy, of an original Rivett 608 Lathe Bulletin (608D). The bulletin is a lot more than just a sales flyer; It should almost be considered a operator’s and set up manual. The bulletin shows some of the accessory set ups in use and descriptions of each accessory. There is even a gear chart included plus the contents listed below. Contents:Angle Iron………………………………………………………………………….18ArborsInternal Wheel……………………………………………………….10Bench, Unit………………………………………………………………………..23Cabinet, oak………………………………………………………………………25Cabinet, steel……………………………………………………………………..33Carriage and Saddle…………………………………………………………….5Centers……………………………………………………………………………..20Change Gears…………………………………………………………………….4Chucks- Center………………………………………………………………….20Drill, Jaw and Step………………………………………………………………21Collets………………………………………………………………………………21Cutting Off and Forming Slide……………………………………………….17Cutting Off and Turning Slide…………………………………………………17Dog, Clamp……………………………………………………………………….18Drawer, Wooden Bench Type……………………………………………….23Drives- Diagrams………………………………………………………………..30Overhead C’shaf…………………………………………………………………27Overhead C’shaft with aux. C’shaft att…………………………………….27Horizontal Safety…………………………………………………………………22Horizontal Safety with aux. C’shaft att……………………………………..23Motor Jackshaft………………………………………………………………….33Speed Box Motor……………………………………………………………….26Speed Box Motor, Overhead att. Motor Drive…………………………26Electrical Controllers……………………………………………………………25Gear Tables- English……………………………………………………………28Gear Tables- Metric…………………………………………………………….29Grinder, Traverse………………………………………………………………..15Grinding Attachments:Belt DrivenInternal, Ecc. Slide Rest Type………………………………………………10External, Ecc. Slide Rest Type………………………………………………10Internal, Rocker Tool Post Type…………………………………………….10External, Rocker Tool Post Type……………………………………………10Grinding Attachment:-Unit Motor Drive Internal set-up…………………………………………………………………….9External set-up……………………………………………………………………9Indexing Attachments:Change Gear Lathe…………………………….13Gear Box Lathe………………………………………………………………….13Interlock, Carriage………………………………………………………………5Knurling Attachment…………………………………………………………….8Lever Chuck Closer:- Change Gear Lathe……………………………….4Gear Box Lathe………………………………………………………………….4Milling AttachmentsCarriage………………………………………………12Slide Rest………………………………………………………………………….12Thread………………………………………………………………………………14Traverse……………………………………………………………………………14Motors and Controllers………………………………………………………..25Oil Pan, on legs…………………………………………………………………..24Oil Pump and Piping…………………………………………………………….24PlatesDriving and Face……………………………………………………..19Quick Change Gear Box………………………………………………………4Relieving Attachment…………………………………………………………..15Rests:Ball Turning…………………………………………………………….11Comp. Slide, Eccentric…………………………………………………………6Comp. Slide, Rocker…………………………………………………………..7Follower……………………………………………………………………………18Steady………………………………………………………………………………18Tee…………………………………………………………………………………..18Triangle……………………………………………………………………………..18Saw Table…………………………………………………………………………18Slotting Attachment……………………………………………………………..13Slotting and Milling Fixtures…………………………………………………..18Specifications……………………………………………………………………..33Spiral Attachment………………………………………………………………..15Tailstocks:Standard………………………………………………………….8Set Over……………………………………………………………………………8Taper Attachment……………………………………………………………….8Thread Dial………………………………………………………………………..9Thread Tool……………………………………………………………………….5Tools:Ecc. Slide Rest Type………………………………………………..11Rocker Tool Post Type………………………………………………………..6Treadles, Latch…………………………………………………………………..7Turrets, Automatic Indexing…………………………………………………..23Turret Attachment, Tailstock…………………………………………………16Turret Tools……………………………………………………………………….16Vises:Ecc. Slide Rest Type………………………………………………..8Rocker Tool Post Type………………………………………………………..19 Overview:I have collected this information for many years and have found the information they contain to be priceless in using and setting up the machines properly. I believe this manual will be a valuable resource of knowledge that will provide a lot of helpful information that is often hard to find. My manuals are not photocopies. I maintain a high standard of quality in my reproductions. Most of the manuals I reproduce look better than their originals. I have professionally digitally edited every page, and removed stains, wrinkles and handwriting. All of the manuals are printed on thick white paper to withstand shop wear and tear Visit our eBay Store!We have over 1,100 manuals available. From our shop to yours. We get this. But you get this! Why settle for anything less?We can’t make pictures a lot better than the original, but we can fix everything else. Shipping: We ship every M-T-W-T-F except US holidays. All of our manuals are shipped with Delivery Confirmation. We stamp “Do Not Bend” on them to ensure that your manual arrives quickly in good condition. Any package that weighs more than 15.9 oz cannot be shipped First Class, and will be shipped Media Mail. Priority and Express mail options are available to purchase. Since we offer free shipping, we cannot reship manuals for free, due to inaccurate or insufficient addresses. Reshipping Fees for inaccurate or insufficient addresses: $5.00 for the first manual and $2.50 for each additional manual. Service: We have been providing this service to fellow craftsman and machinist for over 20 years. We treat everyone as we would like to be treated. We try to take care of all our customers. We do more than sell manuals, we have a complete woodworking and machine shop. We operate all kinds of machinery everyday.
